Product ID:INTERSHIELD PRORECO 508, PRA551
MSDS Date:08/19/1997
FSC:8010
NIIN:00N090171
MSDS Number: CHXZN

COURTAULDS COATINGS INC

6001 ANTOINE DR
HOUSTON, TX 77091
US

Emergency Phone: 800-424-9300(CHEMTREC)

Info Phone: 713-684-1563

Cage: 50411

INTERNATIONAL PAINT INC

HOUSTON, TX 77091 US

Telephone: 713-684-1244

Cage: 028S6

METHYL N-AMYL KETONE

CAS: 110-43-0

RTECS: MJ5075000

Fraction By Weight: 25-50%

OSHA PEL 100 PPM

ACGIH TLV: 50 PPM; 9495

TITANIUM OXIDE; (TITANIUM DIOXIDE)

CAS: 13463-67-7

RTECS: XR2275000

Fraction By Weight: 10-25%

OSHA PEL 15 MG/M3 TDUST

ACGIH TLV: 10 MG/M3 TDUST; 9495

ALUMINUM HYDROXIDE

CAS: 21645-51-2

RTECS: BD0940000

Fraction By Weight: 01-10%

OSHA PEL N/K

ACGIH TLV: N/K

SILICA GEL; (AMORPHOUS SILICA)

CAS: 112945-52-5

RTECS: VV7310000

OSHA PEL N/K

ACGIH TLV: 6 MG/M3 S/NIE

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:INHALATION: CAUSES NOSE AND THROAT
IRRITATION. EYE CONTACT: CAUSES EYE IRRITATION. SKIN CONTACT:
CAUSES SKIN IRRITATION. CAN BE ABSORBED THROUGH THE SKIN. MAY CAUSE
ORGAN DAMAGE. INGESTION: MAY BE FAT AL IF SWALLOWED AND MAY CAUSE
ORGAN DAMAGE.
Explanation of Carcinogenicity:NOT RELEVANT.
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

First Aid:GENERAL: IN ALL CASES OF DOUBT/WHEN SYMPS PERSIST, SEEK MED
ATTN. NEVER GIVE ANYTHING BY MOUTH TO AN UNCONSCIOUS PERS. INHAL:
REMOVE TO FRESH AIR. IF DISCOMFORT IS PRESENT/BRTHG IS ABSENT GET
MED ATTN IMMED. EYE: FLUSH IMMED W/PLENTY OF H*2O FOR AT LEAST 15
MIN UNTIL IRRIT SUBSIDES. IF IRRIT PRESISTS, GET MED ATTN. SKIN:
FLUSH W/LRG AMTS OF H*2O. USE SOAP IF AVAIL. REMOVE SEVERLY CONTAM
CLTHG (INC LUDING SHOES) & WASH BEFORE REUSE. IF IRRIT PERSISTS,
GET MED ATTN. INGEST: DO NOT INDUCE VOMIT. KEEP AT REST. GET PROMPT
MED ATTN.

Flash Point:100F,38C
Extinguishing Media:FOAM, CARBON DIOXIDE, DRY CHEMICAL.
Fire Fighting Procedures:USE NIOSH APPRVD SCBA & FULL PROT EQUIP .
ISOLATE FROM HEAT, SPARKS, ELEC EQUIP & OPEN FLAME. IN ABSENCE OF
ELECTRICITY, A WATER SPRAY (A FOG NOZZLE IS PREFERRED) MAY BE USED
TO COOL CNTNRS. DEC OMP & COMBUST PRODS MAY BE TOX.
Unusual Fire/Explosion Hazard:CLOSED CONTAINERS MAY EXPLODE WHEN
EXPOSED TO EXTREME HEAT.

Spill Release Procedures:CONTAIN SPILLED LIQUID WITH SAND OR EARTH. DO
NOT USE COMBUSTIBLE MATERIALS SUCH AS SAWDUST. ABSORB SPILL WITH AN
INERT MATERIAL (EG, DRY SAND OR EARTH), THEN PLACE IN A CHEMICAL
WASTE CONTAINER.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:KEEP CONTAINER CLOSED. LOOSEN CLOSURE
CAUTIOUSLY BEFORE OPENING. STOR IN A COOL, WELL VENTILATED PLACE
AWAY FROM INCOMPATIBLE MATERIALS.
Other Precautions:KEEP AWAY FROM HEAT, SPARKS & FLAMES. PROT MATL FROM
DIRECT SUNLIGHT. GROUND & BOND CNTNRS WHEN TRANSFERRING MATLS.
EMPTY CNTNRS MAY RETAIN HAZS PROPERTIES. FOLLOW ALL MSDS/LABEL
WARINGS, EVEN AFTER T HE CONTAINER IS EMPTIED.

Respiratory Protection:USE NIOSH APPROVED RESPIRATOR IN ACCORDANCE WITH
29CFR 1910.134 TO REMOVE PARTICULATES (AND VAPORS IF THERE IS
OVEREXPOSURE TO VAPORS GENERATED DURING THE PROCESSING THIS
PRODUCT.
Ventilation:PROVIDE SUFFICIENT VENT, IN VOL & PATTERN, TO: A) KEEP TLV
OF HAZ INGREDS BELOW LIMS SPECIFIED IN SECTION 2. B: REMOVE
VOLATILES PRDCE DURING WELDING/ (SUPDAT)
Protective Gloves:CHEMICAL RESISTENT GLOVES.
Eye Protection:ANSI APPROVED CHEM WORKERS GOGGS .
Other Protective Equipment:ANSI APPRVD EMER EYE WASH & DELUGE SHOWER .
AS NEEDED, USE BODY PROTECTION TO AVOID CONTACT WITH PRODUCT.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
VENT: OR CUTTING ON SURFACES COATED WITH THIS PRODUCT.

Boiling Pt:B.P. Text:305F,152C
Vapor Density:HVR/AIR
Spec Gravity:1.226
Evaporation Rate & Reference:SLOWER/ETHER
Appearance and Odor:LIQUID.

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:MAY PRODUCE HAZS FUMES WHEN HEATED TO
DECOMPOSITION AS IN WELDING. FUMES MAY PRODUCE CARBON DIOXIDE &
CARBON MONOXIDE.

Waste Disposal Methods:DISPOSE OF IN ACCORDANCE WITH LOCAL, STATE AND
FEDERAL REGULATIONS. DO NOT INCINERATE UNOPENED CONTAINERS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.